Mustang Bullitt Forum banner

1 - 15 of 15 Posts

·
Registered
Joined
·
650 Posts
Discussion Starter #1
Ford did a great job with retro gauges from the '68 BULLITT mustang. However on the original '68, the gauges where outlined with chrome trim. Somebody I know is producing a chrome trim kit for the gauges....it's in the works....Thoughts? Comments?
 

·
Registered
Joined
·
586 Posts
I must admit, that could be a very nice mod. I'm totally stock right now, but would consider that dash kit. Consider.

I don't know if I'd get away from stock. It would be nice to add a bit of 'ol chrome to the works, however.

That kit really does remind me of the '68s.
 

·
Registered
Joined
·
444 Posts
I like to have a chrome rings. But so far what I've seen out there is not what I'm expecting. I like to see some simple rings for the gauges. All I've seen so far are complete bezel. A little too much for me.
 

·
Registered
Joined
·
1,130 Posts
I would be interested. I think rings around the gauges would look pretty retro....
 

·
Premium Member
Joined
·
8,327 Posts
I looked at those, but I thought they were a bit too thick (compared to the ones on the concept car, which I really liked).

Not bad though, just not as "elegant" as I would like... that didn't sound right did it? :wink:

B-Man
 

·
Registered
Joined
·
1,130 Posts
Karl, those aren't so bad looking. Where did you find them?
 

·
Registered
Joined
·
1,130 Posts
Youch! I just got Pullies and a T/A for a little over that price! Pretty, Spendy, Indeed.......

_________________
DHG #0428
Steeda TriAx
100mm Denscharger
Awaiting Install: 3.73's, Alum Driveshaft
In The Mail: Steeda Pullies and TA

<font size=-1>[ This Message was edited by: Dillo Dave on 2002-02-25 18:10 ]</font>
 

·
Registered
Joined
·
14 Posts
<TABLE BORDER=0 ALIGN=CENTER WIDTH=85%><TR><TD><font size=-1>Quote:</font><HR></TD></TR><TR><TD><FONT SIZE=-1><BLOCKQUOTE>
On 2002-02-25 09:20, kfengler wrote:
Is this what you're talking about...?

</BLOCKQUOTE></FONT></TD></TR><TR><TD><HR></TD></TR></TABLE>

Those would be nicer if they included screws
in a way which resembles the ring around
the shifter on the console. I know it is
just personal taste, but to me it would look
better if it was styled to be consistent with
other already existing trim.

Has any seen anything like that?
 

·
Registered
Joined
·
6,542 Posts
I might be interested if they are subtle enough.
 

·
Registered
Joined
·
2,024 Posts
<TABLE BORDER=0 ALIGN=CENTER WIDTH=85%><TR><TD><font size=-1>Quote:</font><HR></TD></TR><TR><TD><FONT SIZE=-1><BLOCKQUOTE>Dillo Dave

Youch! I just got Pullies and a T/A for a little over that price! Pretty, Spendy, Indeed....... </BLOCKQUOTE></FONT></TD></TR><TR><TD><HR></TD></TR></TABLE>

I know, I am also waiting for mine to arrive. :smile: I take it that you got in on the group purchase?
 

·
Registered
Joined
·
1,130 Posts
Seeing as how my post was done in late February, I don't know which GP you may be referring to. I think I got in a GP from either StangNet or the Corral back then....
 

·
Registered
Joined
·
456 Posts
For $279.00 it better add some HP :smile:
 
1 - 15 of 15 Posts
Top